Shower Bar: How to Install Bathroom Grab Bars

Buy the right safety grab bars

Grab bars are specially manufactured to hold at least 250 lbs. when properly secured. Towel bars and other light-duty bars are not strong enough.

Most shower bars are stainless steel to resist corrosion, but you can also find them with a painted finish in various colors. We purchased our 1-1/2 in. dia. white grab bars at a home center. The 18-in. bar cost about $30; the 24-in. bar about $40. Thinner bars are available, but a standard 1-1/2 in. dia. shower bar like we’re using is just right for most people’s grip. Some bars feature added texture to reduce slipping. Here are a few guidelines for selecting grab bars:

• Purchase an 18-in. or longer bar to mount vertically at the tub edge.
• Locate the studs before you buy a bar to mount at an angle or horizontally on the long tub wall. Then buy a bar that reaches from one stud to the other, usually 32 in. long for a horizontal bar and 24 in. long for an angled bar.
• Buy standard 1-1/2 in. dia. grab bars for most situations. Thinner bars look more like towel bars and may not be strong enough for heavy use.
• Avoid grab bars that leave more than a 1-1/2 in. space between the bar and the wall unless there is a specific reason for using one. A person’s arm could slip into the extra-wide space and become trapped or break during a fall.
• If you’re installing grab bars for a person with special needs, ask a physical therapist or an occupational therapist to help you select the right bars.

Identify where you’ll position your grab bars

Even a solidly anchored grab bar is useless if it’s in the wrong place. What location is best depends on the particular situation. If you’re installing the bars for a person with a disability or injury, have this person help you decide which location will be most helpful. Here are tips for making your home safer for older folks.

A physical therapist or an occupational therapist can also help with this decision. Stud locations are critical for solid anchoring. (Later, we’ll tell you what to do if studs aren’t available.)

Here are guidelines for placing the bars:

• Place an 18-in. to 24-in. long bar vertically at the tub edge to assist in getting in and out of the tub. The bottom of the bar should be 32 to 38 in. above the floor. Position the bar so it can be anchored to a wall stud.
• Mount a bar at an angle between two wall studs on the long back wall of the tub (Photo 7). The bottom of the bar should be about 6 to 10 in. above the top of the tub. For studs 16 in. apart, a 24-in. long bar provides a nice angle. A person can use this grab bar to help lower himself and get up again.
• If this bar will be used primarily by a person sitting in a bath chair, raise the bottom to about 18 in. above the tub.
• Mount a bar horizontally about 36 in. to 38 in. above the bottom of the tub as a convenient handhold while showering.

Locate and mark the stud locations

If you’re mounting your grab bars to standard wood-framed walls, first you’ll have to precisely locate the vertical framing members called studs. Most grab bars have three screw holes in each mounting flange, but you’ll only be able to anchor two of the three screws into a typical 1-1/2 inch wide stud. Use a plastic anchor for the third screw. As long as these screws penetrate at least an inch into sound wood, the grab bar will meet or exceed the 250-lb. load rating required by the government for public buildings. More importantly, it will be strong enough to support you even in the fall.

We’ll show you how to mount grab bars to fiberglass tubs and showers, hollow walls and concrete. Studs are easy to find in walls with only a single layer of drywall over the framing. Rap on the wall with your knuckle until the sound changes from hollow to a dull thud, or use a stud sensor, like in the photo above. Thicker wall coverings like plaster present a greater challenge. Here are a few tips for installing grab bars:

• Remove the access hatch behind the tub drain and peer behind the tub with a flashlight to look for studs.
• Go to the room or closet behind the long tub wall and look for clues to stud locations like nails in the baseboard. Then, measure from a reference point that you can identify when you return to the bathroom.

Finally, make a light pencil mark at the center of each stud.

TMB STUDIO

Mark the sides of the studs for grab bars

When you’ve located what you believe to be the center of the studs, confirm the stud locations and find both edges by probing with a nail. Make a series of holes in an inconspicuous location, like directly above the tile, and mark both edges of the studs.

If wall tile extends to the ceiling, drill 1/8-in. holes with a glass-and-tile or masonry bit in a horizontal grout line instead. Patch the holes later with matching grout or caulk.

TMB STUDIO

Transfer the stud locations to the tile

Extend the stud marks down to the grab bar location with a level. Place a strip of 1-1/2 in. masking tape on the tile to indicate the studs.

TMB STUDIO

Place the grab bar over the studs

Position the grab bar (see “Positioning Your Shower Grab Bars.”) so that at least two of the screw holes align with the studs. Mark the studs and grab bar mounting holes with a grease pencil.

TMB STUDIO

Drill into the studs

Drill a 1/8-in. hole with a glass-and-tile bit at the mark closest to the center of each stud to confirm the stud location. If you hit solid wood, drill the remaining holes. If not, poke a piece of bent wire through the hole and probe until you feel the stud. Reposition the grab bar and mark the holes.

• Pro tip: If you miss the stud, adjust the grab bar location accordingly and drill new holes. In most cases, the unused hole will be covered by the mounting plate on the grab bar.

TMB STUDIO

Caulk the mounting flange

Caulk the back of the shower bar mounting flange with tub-and-tile adhesive or silicone caulk.

TMB STUDIO

Attach the grab to the wall

Use a 1/4-in. glass-and-tile or masonry bit to enlarge the holes. Then use a 5/32-in. wood bit to drill pilot holes into the stud. This will make driving the screws easier. Insert a plastic anchor in the holes in the tile that miss the stud Then screw the shower bar to the wall with No. 10 or 12 stainless steel pan head screws. Make sure the screws penetrate the studs at least 1 in. In most cases, 2-in. screws are long enough.

TMB STUDIO

How to Install Grab Bars When You Can’t Anchor to a Stud

If you simply can’t anchor the shower bar to a stud, you have a few options. The best alternative is to secure wood blocking between the studs. However, this requires opening a small hole in the wall and patching it after the blocking is screwed into place. Work from the backside of the tub wall if possible, where you’re not hindered by ceramic tile or other tub finishes. If you’re lucky, you’ll have a closet or storage area where the wall patch doesn’t have to be perfect.

As a last resort, use toggle bolts or WingIts to mount the shower bar to the hollow part of the wall. The plaster, mortar or tile backer must be dry and solid and at least 5/8 in. thick.

TMB STUDIO

Special anchor for fiberglass enclosures

The Solid Mount solves the fiberglass shower problem. Fiberglass tub and shower enclosures present a unique challenge. You must mount the shower bar to a stud, but the space between the stud and fiberglass must also be filled with something or the fiberglass will bend as you tighten the mounting screws.

TMB STUDIO

Special toggle bolt for hollow walls

Toggler brand toggle bolts work great for hollow walls or steel studs. If you simply can’t mount your grab bar to a stud or solid wood backing, then these Toggler brand 1/4-in. toggle bolts are the thing to use. Follow the instructions on the package to mount the toggle. Then use a 2-in. x 1/4-in. x No. 20 stainless steel machine screw to attach the grab bar to the toggle anchor. Use the same method to mount grab bars to steel studs.

TMB STUDIO

The best way to anchor grab bars to concrete

Plastic plug anchors hold screws tight in masonry or concrete. Anchor grab bars to concrete, concrete block or brick with 1/4-in. x 1-1/2 in. plastic plug anchors and No. 12 stainless steel pan head screws.

Drill a 1/4-in. hole with a masonry bit (you may need a hammer drill for concrete or hard brick). Push the sleeve into the hole and drive in the screw.

TMB STUDIO

Pull on the shower bar to confirm it’s secure

Now’s the time to make sure the shower bar will hold up when it’s really needed, which means you need to do a yank-test. Give the shower bars a good solid yank to test their holding power. With a helper standing by in case the bar comes loose, pull with all your strength.

While you’re at it, consider installing grab bars in other key locations. A vertical or angled bar mounted on the wall to the side of the toilet or a vertical bar installed on the side wall in front of the toilet helps get up or down. Our expert recommended mounting a vertical bar beside the entry door from an attached garage.

Usually, there isn’t a handrail, and negotiating two or three steps with a bag of groceries under your arm is a lot easier and safer with a grab bar to hang on to. Look around and you’ll find other spots where grab bars would make everyday tasks safer and easier.

TMB STUDIO